9 Simple Steps to Waterproofing Exterior Walls

“The foundation of your home is your walls. You need to pay special attention to the exterior walls of your house because the weather out there will not be nice. It isn’t enough to paint the wall to make it waterproof. After dealing with rain, snow, wind, dust, and heat of the outside environment, the paint will begin peeling off.”

Thus, waterproofing is the best way to ensure that your walls are protected and retain your house’s longevity. At the same time, it is vital to reduce your frequent renovation cost. So, here are some of the simple steps for providing effective waterproofing solutions to your home.

Damp carpets and beneath wall coverings can be the most prominent place for mold and mildew growth. Finishing a basement without first dealing with the moisture problems can make health conditions worse and lead to significant damage. Interior waterproofing systems, installed by a professional contractor, can keep the moisture away throughout the home.

9 Simple Steps to Waterproofing Exterior Walls

Step 1: Expose the wall’s outside properly

To start with waterproofing your exterior walls, make sure it is properly exposed to work on. Your house walls possess a lot of dirt, which creates an additional layer over the wall. Get rid of all the filth and dust from the walls. And before doing so, remove all the drainage pipes and the old field tiles to get proper access to every corner and area of the wall.

Step 2: Make sure the walls are thoroughly cleaned

“The outer part of your home’s wall is usually covered with a lot of dust and dirt that sticks to it. To make the process efficient, you need to clear the debris and dust thoroughly. The dirt and debris can be cleaned using a broom, brush, or scraper. Then wash it with a power washer.”

Make sure the walls are thoroughly cleaned

Step 3: You should fill in any cracks you find

Cracks and holes can develop on the exterior walls over time. Follow up the cleaning process with a thorough look at the cracks and holes on the wall. Just fill them up with cement.

Most of the homeowners get worried about cracks in the foundation. But the fact is, not all foundation cracks affect the home’s structural integrity. Sometimes cracks can be caused by shrinkage during the concrete curing process. These unsightly, non-structural shrinkages, commonly known as hairline cracks, don’t put your home in immediate danger. But on the other hand, structural cracks are serious business.

All over the internet and TV you find websites and programs with step-by-step guides of DIY foundation repair. But the truth is that a foundation should not be experimented on in a DIY project. Foundation repair requires years of experience and specialized tools. When it comes to foundation repair, contact a foundation repair expert.

The cement mixture can penetrate inside the cracks and seal them. Make sure to remove the loose cement from the wall before you apply the cement.

Step 3: You should fill in any cracks you find

Step 4: Seal the cement with waterproofing sealer

If you want to make sure your wall is waterproof, you need to apply a cement waterproofener. After applying the cement in the crevices, let it dry, then apply the waterproof paint seal for the walls. Let it become dry after that.

Seal the cement with waterproofing sealer

Step 5: Choosing the right water-proofer

There are a lot of products that are waterproof. You have to pick the one that goes with the wall. The water-proofer should be selected based on whether the wall is concrete or silicate.

You can choose between a concrete coating, paint, or seal. Pick a plaster waterproof Additive to strengthen your walls.

Step 6: The water-proofer should be applied

Apply the water-proofer thoroughly on the walls with either a roller or brush. If you want to apply more than one layer, give a thin coat. Add the second coating after the first one is dry.

Step 7: Tar and heavy-duty membrane should be applied

“If you want to add more strength to the layer, you need to use a tar-based pitch after you’ve dried the cement. You can apply it on the wall.”

After that, you need to apply a heavy-duty plastic or rubber membrane, which will ensure the proper care of your walls

Step 8: Gravel may be added

A proper base for the trench is below the footer. The drainage pipes are going to get adequate support from a 34-inches gravel base. Gravel is long-durable and provides enhanced protection.

You need to lay the gravel and the drainage pipe-cover. Next to the footer, level the gravel position and then back-fill it. Make sure the pipe is covered for at least 3-inches.

Step 9: Barriers made of fabric can be added

Attach the pipe with a fabric barrier. Ensuring a fabric barrier is going to keep dirt out of your system. Then build the top of the dirt relatively high and allow it to settle for a while. Slope the ground away from the walls for the run-off after.

Conclusion:

Good waterproof gives your home a new life and strength to deal with outside issues. If you want good waterproof solutions for your walls, Magicrete is here to help. At a very low and affordable price, Magicrete can provide you proper weatherproofing.

Leave a Reply

Your email address will not be published. Required fields are marked *